4/1/2024 0 Comments Best openttd newgrfTo perform the mass-upgrade, head to ‘All Trains’ / ‘Manage List’ / ‘Replace Vehicles’ as usual. You can also ‘mass-upgrade’ wagons! This is quite important since monorail wagons have higher capacity. You can convert all the rails in the entire map to the monorail rail type, using the ‘convert to monorail’ tool. Once all trains (engines+wagons) are upgraded, When the monorail locomotive is out, you can simply ‘mass-upgrade’ all trains to the newer train engine. Press arrow keys to scroll the map, then move the cursor to the lowermost part of the map, then release the left mouse-button. Zoom out, to see the biggest part of the map.Select the ‘convert to universal’ tool, located in the ‘universal rail’ build railway menu.To convert all the rails in the entire map at once to universal: The conversion tool is able to convert the track to universal, regardless of whether there’s a train on it or not. Straight from the game: go to NewGRF Settings, Check Online Content, search for “Universal Rail Type”,ĭownload it, and move it to the “Active NewGRF Types”. ‘Game Options’ and change the ‘Base Music Set’.ĭrastically simplifies rail upgrade to monorail/maglev. The game should automatically activate the new music via the orig_dos.obm config file. Copy it to /usr/share/games/openttd/baseset/.obtain the GM.CAT file from the DOS version of the game.The new open-source music is awesome! However, if you’re a huge fan of the original music, The best setup is 2-4 stations with two-rail paths, middle stations are RoRo.Next train arrives to a nearly-empty station and departs faster, thus catching up to the first train. More than 4 stations (assuming two-rail paths+stations) tends to create a clogging effect: first train takes all the passengers.The passengers don’t care - two stations is enough.Trans-map magistral sounds lovely but doesn’t make any sense within the rules of OpenTTD: I never needed the “Pre-signals” and they’re gone from the OpenTTD game anyway.“show reserved tracks” setting, as shown in the Signals tutorial. To see a visualisation how the trains are ‘allocating rails’, I highly recommend to enable the “highlight reserved tracks” or.Make sure to add a bit of offset afterĪ crossing, so that trains are not stopped by the signal and blocking a crossing. Two-rail paths: use the “One-way path signal” only.See “Basic two-way station” in the Signals tutorial. 1-rail paths and stations: use the ‘Regular’ path signal, facing towards the station/path.Only use the path signals in the game, and use them as follows: In the newest OpenTTD they’re gone and completely replacedīy path signals - that’s excellent since they’re much better. In the old TTD there were only block signals. Ideally use curvature of 4 or 5 wagons in the curve. Slowing down longer Maglev from 640 km/h to 264 km/h is a pain to watch :-D You can also mass-upgrade wagons! Read below. You can mass-upgrade all your trains to a newer train engine easily, via ‘All Trains’ / ‘Manage List’ / ‘Replace Vehicles’. It is possible to remove just a part of a station, by using the ‘Removal tool’. Tip: You can mass-convert to electrified rails easily, by employing Universal Rail Type (below). Please find more on the Types of Railway here. If you are a newbie, just start with the ‘Temperate’ map. In the ‘Temperate’ map type, as per List of Train engines. Remember that the best train engine in the game (Lev4 Chimaera Maglev) occupies two carriage slots, leaving Use the stations of length 5 as the bare minimum (10 carriages including the engine). It bundles withĪ new open music, graphics data and everything, in order for you to run and play the game. I love this old DOS/Windows game, and the brilliant OpenTTD projectĪllows you to install and run the game easily, in any major OS.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |